place and play bluetooth ? module new pan1322 series panasonic new product introduction all-in-one, place and play bluetooth module introducing panasonics next generation, smartphone compatible, place and play bluetooth module, the pan1322 series . this module features an embedded microcontroller, bluetooth 2.1 + edr stack, serial port profle (spp), at command set api and antenna. this cost engineered solution is based on a single chip solution that integrates an arm7tdmi processor with a bluetooth controller. the bt 2.1 + edr stack provides secure, reliable, high speed data connections using secure simple paring (ssp) eliminating manual password creation. embedded serial port profle (spp) frees application resources while the at command set api creates a simple frmware interface using modem commands. an onboard antenna does away with 2.4ghz rf circuit complexity. created with the design engineer in mind, product design cycles are greatly reduced using panasonics reference design and design review services. pcb layouts are simplifed using available gerber fles and minimized with panasonics tiny footprint technology. the module is and is just 15.6mm x 8.7mm x 2.8mm and fully shielded to improve immunity. gpio is exposed using at commands. all panasonic bluetooth rf modules carry fcc, ic, ce bluetooth certifcations. the pan1322 series recognizes apples authentication coprocessor and supports bluetooth serial port profle (spp) data communication 1 with apples iphone and ipad ? *. connectivity also includes android, smart phones and all bluetooth enabled devices 2 . panasonic remains committed to customers as a module manufacturer by extending product life using legacy footprints and frmware interfaces to make the pan1322 series fully compatible with the module it replaces, the pan1321 series . hardware and frmware prototyping and testing are accelerated using the eval_pan1322 development kit and spp toolbox development environment. ? bluetooth version 2.1 + edr ? spp device a and b, rfcomm profles ? industrial temperature range, -40 to +85c ? no external components needed ? onboard voltage regulator, v in =2.7 to 3.6 v ? integrated arm7rdmi 32-bit processor w/patchable eeprom ? 3.25 mbaud uart ? gpio w/interrupt and wake-up capabilities ? ios and android devices ? wireless sensors ? cable replacement ? industrial ? medical ? automotive website: www.panasonic.com/industrial industrial@us.panasonic.com 1-800-344-2112 copyright ? 2013 panasonic corporation of north america. all rights reserved. specifcations are subject to change without notice. pan1322 series npi, fy13-046-xxx features applications rohs compliant *apple ipad and iphone are trademarks of apple inc 1. apple authentication coprocessor and mfi certifcation is required. 2. connectivity requires that devices support bluetooth serial port profle
eeprom i 2 c ceramic antenna filter / matching balun pmb8754 bluemoon unicellular crystal 26 mhz voltage regulator vdd1 vdd_uart uart gpio v supply block diagram (pan1322-spp) parameter value condition receiver sensitivity -86 dbm typ. ideal signal output power +3 dbm typ. @ 50 ohm antenna pin power supply 2.7 to 3.5 v single voltage operation ultra low power mode 80 a t = 2.5 c acl (transmit 3-dh1) 40 ma enhanced data rate, 531.2kb/s acl (receive 3-dh1) 37 ma enhanced data rate, 531.2kb/s operating temperature -40 to +85 c technical characteristics part number description enw-89841a3kf pan1322 bluetooth module, spp, integrated antenna eval_pan1322 pan1322 evaluation kit ordering information website: www.panasonic.com/industrial industrial@us.panasonic.com 1-800-344-2112 copyright ? 2013 panasonic corporation of north america. all rights reserved. specifcations are subject to change without notice. pan1322 series npi, fy13-046-xxx for detailed specifcation information on the pan1322 place and play bluetooth module, visit our website at: http://www.panasonic.com/rfmodules/ additional information
|
